 | PRODUCT SPECIFICATIONS Heating Element Model: EP-30-2-44W-24V
Output Wattage (at 24 Vac): 14.0 W/ft (45.9 W/m) @ 68ºF (20ºC)
Nominal Resistance: 41 Ω/ft (13 Ω/m) @ 68ºF (20ºC)
Width: 12" (30.5 cm) Length: Cut to Order Thickness: 3/64" (1.2 mm) | | | - STEP Sunroom™ is designed to provide heated floors in sunrooms, conservatories, etc. For these applications, the floor covering is limited to concrete, tile and stone.
- STEP Sunroom™ has a higher wattage output than the standard residential element, as these types of constructions have high heat losses.
- A heat loss calculation is required to find out if STEP Sunroom™ can sufficiently heat a sunroom all year round. This will depend on the type of construction and insulation values of the substrate, ceiling and windows.
- STEP Sunroom™ heating elements are normally connected to a 24V step-down transformer but they can also run on solar or wind power.
- STEP Sunroom™ is self-regulating and cannot overheat, thereby using less electricity.
- STEP Sunroom™ is strong, thin and flexible, easy to install and can be cut to size on the job site.
| System Components |  | HEATING ELEMENT (EP-30-2-44W-24V) Low voltage (24V, AC or DC), self-regulating Positive Temperature Coefficient (PTC) semi-conductive polyethylene. Patented. Cut to order with 174 feet maximum shipping spool length. | | |  | CONNECTOR & TAPE KIT (C&T-10) Includes (10) CON-DB Crimp Connectors, (1) 15” long piece of TAPE-1 Sealant Tape, (1) Label-1, (1) Label-2, and an installation brochure. Contains material to connect and seal five heating element strips to extension wires. | | |  | TRANSFORMER (EP-150-US, EP-300-US) Low voltage dry type isolation transformer. 120 Vac primary and 24 Vac secondary. NEMA 3R enclosure. | | |  | STEP TRANSFORMER (STEP-500VA, STEP-1000VA, STEP-1500VA) Low voltage dry type isolation transformer. 120 / 240 / 277 Vac primary and 24 Vac secondary. Extruded aluminum profile enclosure w/ heat sink. Patent pending. | | |  | EXTENSION WIRE (TCu14-XXX-B/-W, TCu12-XXX-B/-W) #14 (or #12) AWG stranded tinned copper (TCu) PVC insulated wire, 300 Vac, 105°C. Used to extend heating element bus braid wires to TB-4X5A Terminal Board.
Color Code: -B indicates black; -W indicates white Spool Length: XXX = 50, 100, 150, 250 or 500 feet | | |  | CRIMP TOOL (TOOL-PRO) Used to crimp CON-DB crimp connector. TOOL-PRO crimp tool is required as it is specially designed to properly crimp CON-DB crimp connector. Tool may be purchased or rented. | Optional Components |  | TERMINAL BOARD (TB-4X5A) Fused Terminal Board, 24 Vac, four 5A PTC fuses, set screw lug terminals sized for #14-#4 AWG wires, terminal assignments – one primary hot, four fused secondary hot, and three neutrals. | | |  | TERMINAL BOARD ENCLOSURE (TBE-4, TBE-6) Housing for TB-4X5A Terminal Boards enclosed in extruded aluminum profile w/ heat sink. Available in two sizes: TBE-4 (four TB-4X5A Terminal Boards max.) & TBE-6 (six TB-4X5A Terminal Boards max.). | | |  | MICROREG CONTROLLER (MICROREG) Electronic power controller with relay output for infinitely variable setting of requested heating output, up to 10A. | | |  | DIGI-LUX CONTROLLER (DIGI-LUX, DIGI-Therm, DIGI-Reg-1, DIGI-Reg-2) Electronic Thermostat/Regulator combination (DIGI-LUX) used for zone control of STEP Warmfloor™ system. Thermostat (DIGI-Therm) can be flush wall mounted in single gang box. Each Regulator can control up to 2,500W of connected load. Up to three additional Regulators (DIGI-Reg-2) can be connected to first Regulator (DIGI-Reg-1) to allow for group control of up to 10,000W of connected load. |
Related Links...
|