 |  PRODUCT SPECIFICATIONS
Heating Element Model:
EP-30-2-36W-24V
Output Wattage (at 24 Vac):
11.0 W/ft (36.1 W/m) @ 68ºF (20ºC)
Nominal Resistance:
50 Ω/ft (16 Ω/m) @ 68ºF (20ºC)
Width: 12" (30.5 cm)
Length: Cut to Order
Thickness: 3/64" (1.2 mm) | |
- STEP RV™ is designed to provide heated floors in RV’s, motor homes, boats, etc.
- STEP RV™ has a higher wattage output than the standard residential element, as these types of applications normally have higher heat losses.
- A heat loss calculation is required should the customer request to use STEP RV™ as the sole heating system.
- STEP RV™ heating elements are normally connected to a 24V step-down power supply but they can also run on solar or wind power.
- If STEP RV™ heating elements are connected to 12 Volts AC or DC, the power will be 4 times less .
- STEP RV™ is self-regulating and cannot overheat, thereby using less electricity.
- STEP RV™ is strong, thin and flexible, easy to install and can be cut to size on the job site.
|
| System Components |  | HEATING ELEMENT (EP-30-2-36W-24V)
Low voltage (24V, AC or DC), self-regulating Positive Temperature Coefficient (PTC) semi-conductive polyethylene. Patented. Cut to order with 174 feet maximum shipping spool length. | | |  | EPI-LX POWER SUPPLY (EPI-LX-500, EPI-LX-1000, EPI-LX-1500)
Low voltage dry type isolation power supply. 120 / 208 / 230 Vac primary and 24 Vac secondary. Extruded aluminum profile enclosure w/ heat sink. Primary and secondary circuit protection. RoHS compliant interface board. For indoor use only. Patent pending. | | |  | EPI-LX-R POWER SUPPLY (EPI-LX-R-500, EPI-LX-R-1000, EPI-LX-R-1500)
Low voltage dry type isolation power supply with regulator. 120 / 208 / 230 Vac primary and 24 Vac secondary. Extruded aluminum profile enclosure w/ heat sink. Primary and secondary circuit protection. RoHS compliant interface & regulator board. For indoor use only. Patent pending. | | |  | EXTENSION WIRE (TCu14-XXX-B/-W, TCu12-XXX-B/-W), TCu10-XXX-B/-R)
#14, #12 or #10 AWG stranded tinned copper (TCu) PVC insulated wire, 300 Vac, 105°C. Used to extend heating element bus braid wires to EPI-LX / EPI-LX-R power supply.
Color Code: -B indicates black; -W indicates white; -R indicates red
Spool Length: XXX = 50, 100, 150, 250 or 500 feet | | |  | CONNECTOR & TAPE KIT (C&T-10)
Includes (10) CON-DB Crimp Connectors, (1) 15” long piece of TAPE-1 Sealant Tape, (1) Label-1, (1) Label-2, and an installation brochure. Contains material to connect and seal five heating element strips to extension wires. | | |  | CRIMP TOOL (TOOL-PRO)
Used to crimp CON-DB crimp connector. TOOL-PRO crimp tool is required as it is specially designed to properly crimp CON-DB crimp connector. Tool may be purchased or rented. |
| Optional Components |  | MICROREG CONTROLLER (MICROREG)
Electronic power controller with relay output for infinitely variable setting of requested heating output, up to 10A. | | |  | EPI-LX-TH (NON-PROGRAMMABLE) THERMOSTAT (EPI-LX-TH)
The EPI-LX-TH is a non-programmable thermostat for use with the STEP Warmfloor™ system (in conjunction with the EPI-LX-R power supply series). Features include an easy-to-read backlit display, three temperature conrol modes, a slim contemporary design, and precise temperature control. Up to 20 EPI-LX-R power supplies can be connected to one EPI-LX-TH thermostat. | | |  | EPI-LX-THPR (7-DAY PROGRAMMABLE) THERMOSTAT (EPI-LX-THPR)
The EPI-LX-THPR is a 7-day programmable thermostat for use with the STEP Warmfloor™ system (in conjunction with the EPI-LX-R power supply series). Features include a large, easy-to-read backlit display, three temperature conrol modes, a slim, attractive design (hides programming buttons), and precise temperature control. Other features include 12 or 24 hour programming, up to four programs per day on both weekdays and weekends, and the ability to retain all programming settings in the event of power failure. Up to 20 EPI-LX-R power supplies can be connected to one EPI-LX-THPR thermostat. | | |  | FLOOR SENSOR (EPI-LX-SEN)
Floor temperature sensor. Required when using F mode & AF mode on EPI-LX-TH & EPI-LX-THPR thermostats – not required for A mode. Leads are 15 feet in length. | | |  | TERMINAL BLOCK (T-BLOCK)
Two-pole, power terminal block. Set screw lug terminals sized for #14-#4 AWG wires, terminal assignments – one HOT bar and one NEUTRAL bar. Both bars have four lugs. | | |  | TERMINAL BLOCK ENCLOSURE (TBE-4)
Housing for T-BLOCK power terminal blocks, enclosed in extruded aluminum profile w/ heat sink. Fits up to four terminal blocks. | | |  | POWERED CRIMP TOOL (KWIR)
Used to crimp CON-DB crimp connector. KWIR powered crimp tool is cordless and is specially designed to properly crimp CON-DB crimp connector. Operates on 12V rechargeable battery. Tool can only be purchased. Battery and charger included. |
Related Links...
|
